# Nutek Laser Setup This section describes the setup and configuration required for the Nutek Laser equipment. ## Setup To establish communication with the equipment, configure the following automation parameters with valid values. Additional infrastructure configurations may also be required, such as firewall inbound and outbound rules, antivirus exclusions, network switch port availability, and any other settings necessary to allow data traffic between MES and the equipment. ## Connection Configurations The following configuration parameters can be defined in the *IoTMetaDataDefinition* Smart Table. | Name | Description | | :----------------------------- | :------------------------------------------------------------------------------------------------------------------------------ | | **ServerAddress** | IP address on which the server listens for incoming connections. Leave empty to listen on all network interfaces (`0.0.0.0`). | | **ServerPort** | Port number on which the server listens. The default value is `80`. | | **ServerProtocol** | Protocol used for data exchange. The default value is `HTTP`. | | **ServerCertificateAuthority** | Certificate Authority. Can be specified either as a file path or as the certificate content in plain text. | | **ServerCertificate** | Server certificate. Can be specified either as a file path or as the certificate content in plain text. | | **ServerKey** | Private key associated with the server certificate. Can be specified either as a file path or as the key content in plain text. | | **GetProgramNameDEE** | DEE executed for requests to `/getprogramname`. If not specified, the default value is `SMTLaserMarkerRequestOrder`. | | **GetMarkingDataDEE** | DEE executed for requests to `/getmarkingdata`. If not specified, the default value is `SMTNutekRequestSerialNumber`. | | **SendResultDataDEE** | DEE executed for requests to `/sendresultdata`. If not specified, the default value is `SMTNutekCreateMaterials`. | ## Driver Definition The Automation Driver referenced by the Automation Controller as **RestServer** is **NutekLaser_Driver**. ### Protocol The following Automation Driver protocol is used by the Automation Controller: - **RestServerProtocol**, implemented using the custom package *`@criticalmanufacturing/connect-iot-driver-restserver`*. ## NutekLaser_Driver ### Properties The following table describes the properties available in the **NutekLaser_Driver**. | Name | Property Device Id | Type | Request Component Type | | :-------------- | :----------------- | :------ | :--------------------- | | MESSAGEID | MESSAGEID | Integer | Body | | USERNAME | USERNAME | String | Body | | WORKORDER | WORKORDER | String | Body | | MACHINEID | MACHINEID | String | Body | | DEFPRODFILENAME | DEFPRODFILENAME | String | Body | | PCBPERBOARD | PCBPERBOARD | Integer | Body | | PRODUCTS | PRODUCTS | Object | Body | | MARKINGRETURN | MARKINGRETURN | Object | Body | | RequestID | RequestID | String | RequestId | ### Events The following table describes the events defined in the **NutekLaser_Driver**. | Name | Property Device Id | Request Method | | :------------- | :----------------- | :------------- | | getmarkingdata | /getmarkingdata | POST | | getprogramname | /getprogramname | POST | | sendresultdata | /sendresultdata | POST | ### Event Properties The following table describes the event properties available in the **NutekLaser_Driver**. | Event Name | Property Name | | :------------- | :------------ | | getprogramname | RequestID | | getprogramname | MESSAGEID | | getprogramname | MACHINEID | | getprogramname | USERNAME | | getprogramname | WORKORDER | | getmarkingdata | RequestID | | getmarkingdata | MESSAGEID | | getmarkingdata | MACHINEID | | getmarkingdata | USERNAME | | getmarkingdata | WORKORDER | | getmarkingdata | PCBPERBOARD | | getmarkingdata | PRODUCTS | | sendresultdata | RequestID | | sendresultdata | MESSAGEID | | sendresultdata | MACHINEID | | sendresultdata | USERNAME | | sendresultdata | WORKORDER | | sendresultdata | MARKINGRETURN | ### Commands The following table describes the commands available in the **NutekLaser_Driver**. | Name | Command Device Id | | :--- | :--- | | RequestReplyCommand | RequestReplyCommand | ### Command Parameters The following table describes the command parameters available in the **NutekLaser_Driver**. | Name | Type | Reply Parameter Type | Is Mandatory | Command Name | | :--------- | :------ | :------------------- | :----------- | :------------------ | | RequestId | String | RequestId | Yes | RequestReplyCommand | | StatusCode | Integer | StatusCode | Yes | RequestReplyCommand | | Body | Object | | | |